Blog made by Sonja Bendova through the Xara Web Designer. All rights reserved.
Eines Armbandes im zwei Stunden? Zuversichtlich... Es gibt kein besseres Gefühl, als wenn man an-oder als Ergänzung etwas, das ich mir selbst gemacht genommen! Wissen Sie es? Wenn nicht, versuchen ... und glauben Sie mir, werden andere das bemerken ... Sie wissen nicht, was sie als Geschenk zu Ihrem Freund, Mama, Tante oder andere Frau geben? Original, phantasievoll und völlig neu sein? Machen Sie ihnen ein Geschenk! Versuchen Sie, das Armband für zwei Stunden. Von Ihrem Ergebnis und die Freude der Empfänger - Sie werden glücklicher sein. Das habe ich ein paar Jahren, wenn die meisten der Geschenke, die ich mit der Hand zu machen. Wie es zu tun? Wählen Sie die Größe der Unterlage nach Ihrem Wunsch - die Länge nach dem Umfang Ihres Handgelenks und die Breite nach Ihrem Ermessen - dazu zählen sie 3 Vierecke auf allen 4 Seiten für die Einlage. In die Schleife des Hakens fädeln Sie den gewählten Streifen von Stoff, oder Garnes und den Rand um fädeln Sie durch alle Schleifen rund herum.   The purpose of this whip stitching around is covering the canvas edges completely. When you finish this covering on the edges, pull the fabric out of the locker hook and let there cca 5-10 cm long tail. Thread the locking medium cotton twine to the locker hook eye and its end tie by simple knot anywhere on the canvas. After finishing of your project you will untie it and hide it in finished loops. Choose the fabric strip you want to start filling the interior space of your bracelet. Insert the hook from the top down through the canvas and with the help of the other hand pull the first loop on the canvas. Again insert your locker hook through the canvas a pull another loop. One you have on the hook 6-8 loops, pass through your locker hook with locking medium cotton twine. This will secure your created loops. Continue by thi sway in your chosen pattern – around, horizontally, vertically, across (it depend on your fantasy) or create spiral patterns as I did in this demonstration. Sooner or later you get into a situation when you will need to extend your fabric strip. Someone is fabric strips sewing together, someone begins and ends after each strip. The most proven way how to combine two fabric strips together for me are steps on photos below. Fold the end of used strip and the new fabric strip for cca 1 cm and cut 0,5 cm long section. Put the end of new fabric stip on the top of the tail of used fabric strip and cover them in the place of created holes. New fabric strip thread through the both holes (from below). Tug at both strips firmly but not excessively (not to tear them). Next I continue in making loops. The knot will merge between the loops or at the bottom of the canvas. Continue in making your pattern or let your creative energy flow as I did. When is your bracelet fulfilled by the loops, you will finished remaining tails of fabric strips. Pull the ends up on the canvas by tapestry needle and throught these ends in next loops raw by (at least) five loops.  Remaining tail cut by scissors. I decided to use several beads to the center of created flowers. These I pin there by a thread normally. Only fastening is missing – use closing clip or thread 30 beads and use them as a little eye round the small button (sewn on the opposite side). Devise and create yourselves! It is easy, isn't it? Do you believe me that this bracelet-making took me 2 hours only? With taking photos, of course... If not, come to some of my courses and you will see how easy and amazingly creative the locker hooking is.
CZ EN DE Home Kontakte Eshop Was ist Locker Hooking und was brauchen Sie? Blog Buchen Videos Musters Galerie Über mich DE